تويت
ممكن خدمة مع كامل الدعاء.... اريدبعض القطع الالكترونية ولقد بحثت كثيرا ولم اجدها والظاهر لديك خبرة كبيرة بالالكترونيات وانا من سوريا ومستعد لكافة التكاليفC1 1 uF tant. @ 25 volts Min.
C2 4.7 to 10 uF Tant. @ 10 Volts Min.
C3 4.7 to 10 uF. tant. @ 10 Volts Min.
C4 10 uF. Tant. @ 25 Volts Min.
C5 100 uF. Electrolytic @ 25 Volts
C6 1 uF. Tant. @ 10 Volts Min.
C7 1 uF. Tant. @ 10 Volts Min.
C8 4.7 to 10 uF. Tant. @ 10 Volts Min.
C9 1 uF. Tant. @ 10 volts Min.
C10 1 uF. Tant @ 10 Volts Min.
C11 .1 uF ****lized Polyester Film Cap.
C12 .01 @ 100 Volts "
C13 .01 " "
C14 .01 " "
C15 .001 " "
C16 .01 " "
C17 .0047 " "
C18 4.7 to 10 Mfd. Tant. @ 10 Volts Min.
C19 47 or 100 Pf disk, depending on your requirements.
C20 .01 @ 100 Volts ****lized Polyester Film Caps.
C21 .01 " "
C22 47 or 100 pf Disk, depending on your requirements.
C25 .1 @ 63 Volts ****lized Polyester Film Caps.
C26 .1 "
C27 22 uF Electrolytic @ 10 Volts
C28 .1 @ 63 Volts ****lized Polyester Film Caps.
C29 .01 @ 63 Volts " " " "
C30 .22 or .18 @ 63 volts " " " "
C31 4.7 to 10 uF. Tant. @ 10 Volts Min.
C33 4.7 to 10 uF. Tant. @ 10 Volts Min.
C34 470 uF. Electrolytic @ 10 Volt Min.
D:
D1 1N4937 "High Speed diode."
D2 1N4937 "High Speed diode."
IC Sockets 8 each, 8 pin dips. Highly Recommended.
IC1 REG-1117A-adj (Surface mount "SOT-223" Package. Mounts on copper side.)
OR a MC33269ST-ADJ ("SOT-223 Package" Adjustable version.)
On Both these IC's, it is Not Recommended that you solder the Centre Lead.
Just solder the Two Outside leads and the Heat Tab.
IC2 LT1054-CN8 -(8 pin dip) "Substitute a ICL7660ACPA", it is much cheaper)
ICL7660.....SEE NOTE AT BOTTOM!
IC3 78L05 T0-92 pkg.
IC4 79L05 T0-92 pkg.
Q1 IRF640 or IRF740 (You can cut off heat tab if you wish to reduce height.)
Q2 IRF640 or IRF740 (You can cut off heat tab if you wish to reduce height.)
Q3 2N3819 or 2SK30A(Check PINOUT, Before Installing)
Q4 2N4125 or 2N3906 or almost any PNP type signal transistor will work.
C2 4.7 to 10 uF Tant. @ 10 Volts Min.
C3 4.7 to 10 uF. tant. @ 10 Volts Min.
C4 10 uF. Tant. @ 25 Volts Min.
C5 100 uF. Electrolytic @ 25 Volts
C6 1 uF. Tant. @ 10 Volts Min.
C7 1 uF. Tant. @ 10 Volts Min.
C8 4.7 to 10 uF. Tant. @ 10 Volts Min.
C9 1 uF. Tant. @ 10 volts Min.
C10 1 uF. Tant @ 10 Volts Min.
C11 .1 uF ****lized Polyester Film Cap.
C12 .01 @ 100 Volts "
C13 .01 " "
C14 .01 " "
C15 .001 " "
C16 .01 " "
C17 .0047 " "
C18 4.7 to 10 Mfd. Tant. @ 10 Volts Min.
C19 47 or 100 Pf disk, depending on your requirements.
C20 .01 @ 100 Volts ****lized Polyester Film Caps.
C21 .01 " "
C22 47 or 100 pf Disk, depending on your requirements.
C25 .1 @ 63 Volts ****lized Polyester Film Caps.
C26 .1 "
C27 22 uF Electrolytic @ 10 Volts
C28 .1 @ 63 Volts ****lized Polyester Film Caps.
C29 .01 @ 63 Volts " " " "
C30 .22 or .18 @ 63 volts " " " "
C31 4.7 to 10 uF. Tant. @ 10 Volts Min.
C33 4.7 to 10 uF. Tant. @ 10 Volts Min.
C34 470 uF. Electrolytic @ 10 Volt Min.
D:
D1 1N4937 "High Speed diode."
D2 1N4937 "High Speed diode."
IC Sockets 8 each, 8 pin dips. Highly Recommended.
IC1 REG-1117A-adj (Surface mount "SOT-223" Package. Mounts on copper side.)
OR a MC33269ST-ADJ ("SOT-223 Package" Adjustable version.)
On Both these IC's, it is Not Recommended that you solder the Centre Lead.
Just solder the Two Outside leads and the Heat Tab.
IC2 LT1054-CN8 -(8 pin dip) "Substitute a ICL7660ACPA", it is much cheaper)
ICL7660.....SEE NOTE AT BOTTOM!
IC3 78L05 T0-92 pkg.
IC4 79L05 T0-92 pkg.
Q1 IRF640 or IRF740 (You can cut off heat tab if you wish to reduce height.)
Q2 IRF640 or IRF740 (You can cut off heat tab if you wish to reduce height.)
Q3 2N3819 or 2SK30A(Check PINOUT, Before Installing)
Q4 2N4125 or 2N3906 or almost any PNP type signal transistor will work.